Rolling Code Duplicator 315Mhz 433Mhz Remote Control Detector User Guide
315Mhz 433Mhz Remote Control Detector is the for adjustable Frequency Remote Control Receiver and Replicator.Some customers have no idea about how to use the 315Mhz 433Mhz Remote Control Detector .Bellow OBD2repair.com share you Rolling Code Duplicator 315Mhz 433Mhz Remote Control Detector user manual.
Rolling Code 315Mhz 433Mhz Remote Control Detector and Duplicator
315Mhz 433Mhz Remote Control Detector Rolling Code Duplicator User Guide
Operate Instruction
The machine uses a dedicated 9V power supply.
After setting battery, witch on the left side, after booting, it will show English " Remote control Decode the
tool ". The machine operates at a frequency of 305-433mhz. There are six keys--A, B, C, D, E, F. All
feature set is completed by these six keys, the A-D key is the former group function, E, F keys are the
latter function.
OBD2repair.com 315Mhz 433Mhz Rolling Code Duplicator Notice:
when install the batteries, ensure "+" to "+" and "-" to "-" to make it is possible to supply power for
the machine
Specific operation instructions
A.Press any key to do setting after booting, in the general case each receives a signal, there will be two lines CAPION on the LCD panel, the first line before eight digital is the address of the received signal,
after four is data bits, the second line is before three number is oscillation resistance, followed by four
number is the chip type (received signal can be generated by remote control, infrared magnetic door)
1. when received signal, directly press A or B or C or D can change the received signal data and launch
out
2. when receiving the signal, press the F key, In a lower place of the LCD display show *, the machine
keep the last time received signals, and refused to accept any other signal. We can change the signal
data bits via A, B, C, D key and press E key to launch out the modified encoding
B.Scan Function: when a set of normal use anti-theft host missing accessories, you can use themachine to scan for the coding, then made remote control and other accessories for it.
Specific operation as follows:
Press E key after booting, at the bottom right of the LCD display appears 1.2M*, means the testing
vibration resistance value is 1.2M ohm, press the F key can change the oscillation resistance value,
optional respectively is 1.8M, 2.2M, 3.3M, 4.7M. After confirmed the vibration resistance value, must
provide the data bits, choose any key from A, B, C, D, press E to start scan. Normal band all the scan is
complete need to 10 minutes, LCD screen first line before 8 numbers is changing to scan address bits,
the second line the front changing information is scan times. When scanning to the encoding of the
anti-theft host, the host will make a sound, scanning continues to forward, we press F key, the machine
backward scan, also will slow down, when heard the host sound again, press the E key and hold for more
than 2 minutes the let go, at this time, the appears address bits is the address code of the anti-theft
host(Note: The base operating less skilled, address bits may also scan backward one or two more bits,
you need to use "every three into one" method on the basis of the address code plus one or two, you can
first scan to the address bits then record it by pen, and then every three into one on the basis of the
record address bits, all = 010 010 + 1 = 011 12010122 + 1 = 12012200 And by this analogy, you can get
the real address of the address bits encoding) to determine if the encoding is correct, use below "c"
function to self test encoding.
C.Optional encoding function: it is a test method used when not sure about the address bits.
Specific operation as follows:
Press E key after booting, it will appears the same interface with " B" scan function, press F to select the
appropriate oscillation resistor value, and then press the E key again, on the right of the resistance value
appears one "+" sign, at the top left appears eight address code flashing point, press one or two keys to
increase or decrease the value. Press A or B to increase or reduce value, press C or D to move left and
right, press E again can launch out.
D. Storage Function
1. Turn the power on, when receive a wireless signal, press "E" to store that.
2. Press A and B at the same time. When Lcd display appears " S " sign, press E can call up the stored
encoding, press "A" or "B" or "C" or "D" to launch out the encoding.
3. Forwarding function: Press C and D at same time, when appears "1" sign can activate the forwarding
function. The display appears "/" sign when receiving an unknown code, press the "F" key forwards,
press the "E" key to exit. If known received encoded chip, it will not be forwarded.
OBD2repair.com 315Mhz 433Mhz Remote Control Detector Note:
LCD display show *, the machine refuse to accept any other signal. When you press the F key, the
* disappear and you can receive the signal again.
More detail about 315Mhz 433Mhz Remote Control Detector,pls connect
More detail about ,pls connect
Website:www.obd2repair.com
Skype：obd2repair / eobdscan1
We Chat/ Whatsapp (+86)13728823163
Email: info@obd2repair.com
Facebook: www.facebook.com/obd2repaircom/
